A running list of things we've acquired or found available for sale by Alard Equipment Corporation; used food processing and packaging equipment.

Alard Equipment Corporation, 6483 Lake Avenue, Williamson, New York 14589, 315-589-4511 (phone), 315-589-3871 (fax)

See our full General Listings page

September 2011 Archives

y1018

y1018_email.jpgWALKER 250 GALLON STAINLESS STEEL INSULATED MIX TANK WITH SWEEP AGITATION.

46" inner diameter x 57" deep dish bottom vertical vessel with 3" Tri-clamp center bottom discharge outlet; as well as one 2" threaded bottom side outlet. The vessel is fully insulated with insulation fully shrouded in stainless steel.

Stainless steel agitator support bridge with bridge-mounted baffle, 2"diameter agitator shaft with two blade propellor type sweep agiator. Each blade measures 5" wide by 16" long. The agitator is powered by a 5 HP 230/460 volt 3 phase Eurodrive drive geared for 42 RPM mixer output.

With one hinged top cover and one removable cover to open top. Complete with (4) 3' high stainless steel support leg extensions. The unextended leg stubs place the tank at a 67" infeed height, 6" discharge height, and 95" overall height. The included leg extensions would raise those elevations by about 3'.

In stock complete and in good condition, available for  timely shipment.
Alard item reference #:Y1018

y1129

y1129b_email.jpgKEY ISO-FLO STAINLESS STEEL VIBRATING CONVEYOR with fines removal / dewatering screen. 18" wide x 82" long shaker pan, solid except for a 12" long screen  section near the discharge end with 3/16" perforations, over an underside conical  collection pan tapering to a 6" diameter discharge.

This vibrating shaker was apparently designed with a "low front side" for side-loading or vibratory inspection conveyor usage (in a right to left product flow configuration from the perspective of one standing at the low side), as it has a 4" high sidewall on one side, and an 8"  high sidewall on the other.

Food grade sanitary stainless steel construction, Iso
-flow "isolation" mounts over tubular stainless steel legs set to a 44" working pan height. Complete with 1.5HP 208/230/460 volt 3 phase drive with Key eccentric.

This vibratory conveyor is IN stock in VERY good condition, available for timely shipment.
 
Alard item reference #:Y1129

y1119

y1119g_email.jpgURSCHEL Model J9-A DICER with 9" wide feed belt. A two-dimensional cutter, manufacturer rated  for firm products up to 1/2" with included feed roll, or thicker if product is compressable. Urschel rates the J9A for producing a wide variety of dices and strip cuts. Circular knives can be configured for cuts from 3/16" to2" (4.8mm to 50.8mm), and crosscut spindles are available for cuts from 3/16" to 3"; --cutting a diverse array of productssuch as meats (beef jerky, bacon strips, sausage crumbles), baked goods (pita chips, bread dices for croutons, brownies), and vegetable products (greens, peppers, etc).  Food grade/ USDA sanitary stainless steel construction; including frame, guards, shrouds and cutting spindles.

This J9A is currently set with a 1/4" feed roll, a circular knife spindle that came in set up for 1/2", and a 5/8" crosscut spindle, but we can set the machine up for other dice sizes (please tell us your cutting specification!). It is complete with a factory electrical control panel with a safety interlock system, controlling the 5HP 208/230/460 volt 3 phase drive motor with Stearns brake.

In stock in VERY GOOD operational condition, available for timely shipment.  Alard item reference #:Y1119

y0789

y0789l_email.jpgSTAINLESS STEEL HYDRAULIC BIN DUMPER, with  45" wide x 48" long x 42" deep (internal dimensions) bin holder, floor level infeed, with 39" high pivot point, 135 degree rotation, and 4,000 lb payload capacity. Hold down bar currently positioned at 54" height clearance. Floor level infeed on heavy 1/4" stainless steel angle frame. NEW 3" diameter hydraulic cylinders, new hydraulic power-pack, new hydraulic hoses and new operator controls.

Has footpads that must be SECURELY anchored to the floor for safety/stability.

In stock in EXCELLENT operational, hydraulic, and mechanical condition, ready to go and available for immediate shipment.
Alard item reference #:Y0789

y0895

y0895b_email.jpgAPV Model 6x72x4 STAINLESS STEEL SCRAPED SURFACE HEAT EXCHANGER.
Four six inch diameter by seventy-two inch long swept-surface heat exchanger tubes mounted in a two-over-two quad configuration on a stainless steel frame. Each barrel is jacketed, manufacturer tagged, and National Board coded for 150psi. Each tube has stainless steel rotors with plastic scrapers, 3" product inlet / outlet with Tri-clamp fittings, and each tube is driven by it's own 10HP 3-phase drive. Last used for ammonia cooling.
This four-barrel scrape-surface heat exchanger system came in missing two drives, but is otherwise in stock in very good condition, available for timely shipment.
Alard item reference #:Y0895

y0900

y0900a_email.jpgVOTATOR Model 6 x 72 x 4 STAINLESS STEEL SWEPT SURFACE HEAT EXCHANGER.

(4) 6" diameter by 72" long scraped surface heat exchanger barrels mounted in a two-over-two quad configuration on a tubular stainless steel frame. Two tubes have stainless steel scrapers, while two tubes have macarta scrapers. Each barrel  has 2" product inlet / outlet with Tri-clamp fittings. All the tubes are jacketed, manufacturer tagged, and ASME stamped for 150psi; two are National Board coded. Two tubes have 20HP 3-phase drives, and two have 10HP 3-phase drives.

This four-barrel scrape surface heat exchanger system is in good condiiton, available for timely shipment.
Alard item reference #:Y0900

y0841

y0841_email.jpgHAMILTON 400 GALLON STAINLESS STEEL STEAM JACKETED KETTLE, with TRIPLE MOTION SCRAPER-AGITATOR. 64" diameter x 44" deep hemispherical bottom stainless steel vessel with a 3" center bottom outlet with Tri-clamp connection. Stainless steel steam jacket manufacturer tagged, National Board coded and Canadian Register stamped for 90psi working pressure.

"Triple motion" consists of a main scraper-agitator between two offset perforated paddle agitators, all mounted in  common on a stainless steel bridge that tilts out for cleaning, with a water cylinder power tilt assist. The main agitator is powered by a 5HP 3 phase drive, with 1HP 3 phase drives on each of the offset agitators.

Open top with hinged top covers and hinged safety grid on one side. 66" infeed height, 16.5" discharge height on (4) stainless steel legs. Stainless steel center mounted CIP coil mounted just above the bottom of the main agitator.

In stock in good condition, available for timely shipment.
Ref. #:Y0841

y1151

y1151a_email.jpgGORING KERR Model DSP2 STAINLESS STEEL DIGITAL METAL DETECTOR with NEW STAINLESS STEEL CONVEYOR, 3 7/8" high by 13 7/8" wide usable aperture opening in an all stainless steel washdown-sealed search head enclosure.

The detection head is mounted on a NEW STAINLESS STEEL THROUGH-CONVEYOR, with an 11.75" wide by 60" long interlocking plastic chain type belt running over a UHMW plastic bed, on a tubular stainless steel frame. The conveyor runs in a left to right product flow (from the perspective of the operator control panel), at a 33" working height on height-adjustable foot pads. The conveyor is complete with BELT-STOP-ALARM-REJECT system, with a PVC control box, and .33 HP 110/220 volt single phase washdown drive motor.
y1151e_email.jpg

REFURBISHED metal detector detection head on all NEW conveyor, in stock in EXCELLENT operational, electrical, mechanical, and cosmetic condition, available for immediate shipment.
Alard item reference #:Y1151

y1138_y1139_y1140_y1141

y1138_y1139_y1140_y1141n_email.jpgQuantity (4) MATCHING 300 GALLON STAINLESS STEEL VERTICAL TANKS.
Each tank consists of a heavily built 48" diameter by 48" deep dish bottom vessel with 4" center bottom outlet with flange connection; --with a heavy bolted-on stainless steel top cover with a 16 inch manway, agitator slot, and various inlets. Each has a three leg steel frame painted with "steel-it" metallic paint. One (Y1138) has an insulated cover.
In stock in VERY good condition, available individually or as a matching set of four, available for immediate shipment.
Alard item reference #:Y1141

y1114

y1114j_email.jpgDITO DEAN Model T15S STAINLESS STEEL BATCH PEELER, with interchangeable ABRASIVE AND KNIFE PEELING DISKS.

15" diameter by 9.5" deep peeling chamber manufacturer rated for 15 Kg (approximately 33 lb) load capacity per batch, with hinged top cover with observation window, and rinse water inlet port. 6" high x 6.5" wide side discharge door. 50" infeed height, 33.5" discharge height, on stainless steel support frame with catch pan for peels. Complete with wavy abrasive peeling disk, and knife peeling disk, which can be interchanged at will. Stainless steel and aluminum construction.

110 volt single phase (standard household current) drive motor with operator on/ off and timer controls.

In stock in very good operational condition, available for immediate shipment.
Alard item reference  #:Y1114

y1048

y1048c_email.jpgRIETZ STAINLESS STEEL JACKETED OPEN SCREW BLANCHER. 18" diameter by 14' long open screw with a stainless steel bottom jacket manufacturer tagged and U-stamped for 45 psi steam pressure, as well as (27) steam injection, with valves (two injection points per valve). 38" infeed height to an 18" by 36" infeed opening, with  the remainder of the blancher shielded by two hinged covers. Paddle type right-hand side discharge to an 11" by 18" chute dischraging at a 30" discharge height
Complete with a 3/4 HP drive.
In stock in good condition, available for timely shipment.
Alard item reference Y1048

About this Archive

This page is an archive of entries from September 2011 listed from newest to oldest.

August 2011 is the previous archive.

October 2011 is the next archive.

Find recent content on the main index or look in the archives to find all content.


JOIN our
no-more-than-monthly

Email list!
Email PRIVACY explanation link!

ALARD EQUIPMENT CORP
6483 Lake Avenue
Williamson, NY  14589
315-589-4511
315-589-3871 (fax)