A running list of things we've acquired or found available for sale by Alard Equipment Corporation; used food processing and packaging equipment.

Alard Equipment Corporation, 6483 Lake Avenue, Williamson, New York 14589, 315-589-4511 (phone), 315-589-3871 (fax)

See our full General Listings page

January 2013 Archives

y1725

y1725b_email.jpgURSCHEL Model RA-A DICER, sanitary stainless steel food grade construction, manufacturer rated for USDA sanitary compliance, and for products up to 3.5 inches (7.62cm) in any dimension, to produce large dices / cubes up to 1" (2.54cm) square, and a variety of strip cuts.

This machine cuts in three dimensions, as described more specifically, manufacturer literature specifies slice thickness (crank adjustable) from 1/16th inch to 3/8 inch (1.6mm to 9.5mm), circular knife (change part) cuts from 1/8 inch to 1 inch (3.2mm to 2.54cm), and crosscut knife spindles (change part) from 5/100 inch up to 3 inches (1.3mm to 7.62cm). Currently set for 1/2 inch dices (12.7mm cubes); --please tell us your cutting specification, and if we can (subject to availability) we will set the machine to your cut dimension.

This Urschel cutter is complete with all it's stainless steel steel safety guards and shrouds. It also has safety switches wired to a stainless steel factory installed electrical control panel with a safety interlock system, with a 5 HP 3 phase brakemotor drive.

As of this writing, this machine is in stock, in good condition, available for timely shipment.
Alard item reference #: Y1725

y1571

y1571_email.jpgURSCHEL MODEL H-A DICER, with 7 inch (17.78cm) stainless steel slice shell opening.

Sanitary stainless steel food grade construction, manufacturer rated for USDA sanitary compliance, and for product up to 5.5 inches (14cm) in any dimension, to produce large dices / cubes up to 1 inch (2.54cm) square, and a variety of strip cuts.

This machine cuts in three dimensions, as described more specifically, manufacturer literature specifies slice thickness (crank adjustable) from 1/8 inch (3.2mm) to 3/4 inch (1.9cm), crosscut knife spindles (change part) from 3/4 inch (1.9cm) up to 1.75 inch (4.45cm); --there are special kits available from Urschel to extend the crosscut range to smaller cuts similar to an Urschel G model). Finally, circular knife cuts (change part) from 1/8 inch (3.2mm) up to 3" (7.62cm). Please tell us your cutting specification, and if we can (subject to availability) we will set the machine to your cut dimension.


This Urschel cutter is complete with all it's stainless steel steel safety guards and shrouds. It also has safety switches wired to a stainless steel factory installed electrical control panel with a safety interlock system, with a 2 HP 3 phase brakemotor drive.

As of this writing, this machine is in stock, available for timely service and shipment. Available as-is, or Alard can refurbish (at extra cost) to excellent mechanical and cosmetic condition which would include replating the castings (plating is partially worn away in some places), casters shown in pictures will be removed, & etc.
Alard item reference #: Y1571

y1526

y1526g_email.jpgURSCHEL MODEL H-A DICER, with 10 inch (25.4cm) stainless steel slice shell opening.

Sanitary stainless steel food grade construction, manufacturer rated for USDA sanitary compliance, and for products up to 5.5 inches (14cm) in any dimension, to produce large dices / cubes up to 1 inch (2.54cm) square, and a variety of strip cuts.

This machine cuts in three dimensions, as described more specifically, manufacturer literature specifies slice thickness (crank adjustable) from 1/8 inch (3.2mm) to 3/4 inch (1.9cm), crosscut knife spindles (change part) from 3/4 inch (1.9cm) up to 1.75 inch (4.45cm); --there are special kits available from Urschel to extend the crosscut range to smaller cuts similar to an Urschel G model). Finally, circular knife cuts (change part) from 1/8 inch (3.2mm) up to 3" (7.62cm). Please tell us your cutting specification, and if we can (subject to availability) we will set the machine to your cut dimension.

This Urschel cutter is complete with all it's stainless steel steel safety guards and shrouds. It also has a new style enclosed frame, and safety switches wired to a stainless steel factory installed electrical control panel with a safety interlock system including a 2 HP 3 phase brakemotor drive.

As of this writing, this machine is in stock, available for timely service and shipment. Available as-is, or Alard can refurbish to excellent mechanical and cosmetic condition which would include replating all the castings (plating is worn off) & etc.
Alard item reference #: Y1526

y0932

y0932q_email.jpg MAGNUSON CCM AUTOMATIC CORN CUTTER, Model SC8402L, manufacture literature describes as designed to gently and automatically orient and feed cobs to an aperture-like cutting head which automatically adjusts to the size and taper of the cob as it cuts. The feed system is designed to automatically remove cobs which are too small, and to attempt to clear cutting head jams without operator intervention. Manufacturer rates for 110 to 130 ears per minute (average rate).

Food grade sanitary stainless steel construction, hydraulically powered, with an  approximately 10 gpm hydraulic requirement. Uses water to keep the at a rate of  7 approximately 7 gallons per hour, to lubricate the cutting head.

Complete with (8) hydraulic drives, 16" wide x 20" long infeed belt leading to a 27" diameter sorting bowl for orientation (the "L" in the model number designates "Large bowl". 40" long cob feed belt with reject. Separate 24" diameter sorting bowl. 6' high infeed and 32" high kernel discharge, 42" high cob discharge. Includes an automatic oiler. 220 volt single phase electrical input for control circuit.

Hydraulic power pack (pump and reservoir system) required / not included; available separately.

As of this writing, this CCM CORN CUTTER IS in stock in good condition, available for timely shipment.

Alard item reference #:Y0932


z9315

WEIGH RIGHT Model PMB-2F FRESH-CUT FRUIT FILLER, complete with elevating feed conveyor.



An automatic two-lane linear scale / netweigh filler, manufacturer rated for gentle, fast accurate filling of precut and whole fruit pieces into bags, trays, or tubs, and adjustable for packages from 4 ounce to 10 lb capacity, at speeds from 8 to 24 fills per minute. Manufacturer literature specifies this model for filling apple slices, cantaloupe melon, pineapple, honey-dew melon, watermelon, whole strawberries, grapes, mixed fruit, IQF frozen fruits, "and more". It would apparently work for vegetable products with similar characteristics.

All sanitary food grade stainless steel construction, with rigidized / dimpled non-stick product contact surfaces. Complete with operator control panel with PLC system control, and weigher controls for each of the two scale weigh cells. Uses 110 volt single phase electrical input (standard household current), and pneumatic (compressed air) input.

Includes a Weigh Right Model 10 Z-shaped elevating INFEED CONVEYOR, with a 12.5 inch wide by 8 foot long belt. The gooseneck / Z shape configuration consists of a 2' long horizontal infeed section, a 5 foot long shallow incline section, and a 14 inch long horizontal discharge section. The plastic interlocking chain type belt is not cleated.

The infeed conveyor has a variable speed control on the main panel, and the overall system is tunable for cycle time, speed, etc.

As of this writing, this PMB-F Series netweigh melon filler / fruit & vegetable filler is in stock in EXCELLENT operational, electrical, and mechanical  condition, available for immediate shipment.

Alard item reference #: Z9315

y1341

DOMINO S200W LASER CODER, with DPX 500 fume extractor, touch-screen controls, interlock safety system, and product sensor.






Speed varies with container material, but manufacturer literature rates this 20 watt sealed CO2 scribing laser marking system for up to 300 characters per second in a 2.2 inch square marking field, 3" focus depth, and 24 character fonts with character size from .03 to 1.97".

Touchscreen controller in stainless steel cabinet, runs on Windows 2000 operating system. Fume extractor/air filter in stainless steel cabinet manufacturer rated as IP56 sealed.  Standalone stainless steel laser marking head, rated as sealed to IP55 standard, with cord, for mounting on your existing conveyor line (must be contained in safety enclosure).

This coder requires NO inks or fluids, so it's clean and economical in operation.

As of this writing, this laser marker is in stock in very good operational condition, ready to go, and available for immediate shipment.
Alard item reference #: Y1341

About this Archive

This page is an archive of entries from January 2013 listed from newest to oldest.

December 2012 is the previous archive.

February 2013 is the next archive.

Find recent content on the main index or look in the archives to find all content.


JOIN our
no-more-than-monthly

Email list!
Email PRIVACY explanation link!

ALARD EQUIPMENT CORP
6483 Lake Avenue
Williamson, NY  14589
315-589-4511
315-589-3871 (fax)