A running list of things we've acquired or found available for sale by Alard Equipment Corporation; used food processing and packaging equipment.

Alard Equipment Corporation, 6483 Lake Avenue, Williamson, New York 14589, 315-589-4511 (phone), 315-589-3871 (fax)

See our full General Listings page

May 2013 Archives

y0598

y0598e_email.jpgURSCHEL MODEL MG-1700 COMITROL PROCESSOR, 30 HP 230/460 volt 3 phase motor, microcut head, oil mist lubricator, pipe infeed.

As of this writing, this Urschel Comitrol is in stock in good operable condition, available for timely shipment.

Alard item reference #:Y0598

y1764

y1764a_email.jpgMETAL DETECTOR - SAFELINE DIGITAL STAINLESS STEEL CONVEYORIZED WASH-DOWN METAL DETECTION SYSTEM with PUSH-OFF REJECT, 8.5 inch high by 5 inch wide usable aperture opening.

The all stainless steel washdown sealed search head is mounted on a stainless steel tubular frame BELT CONVEYOR. Previously used on a single belt long process line, this metal detector arrived with no belt or drive, and with 1/2 inch thick (each) UHMW sides running through the aperture, and is shown that way in our pictures of it. The overall aperture height of the search head is 10.75 inches high  by 4 7/8" inch wide, but as it now sits, configured with thick UHMW side rails and a 1 inch UHMW bed with no belt, the AS-IS aperture opening as shown in pictures is 9 3/8 inches high by 3 3/8 inches wide (between the sides).

Assuming a belt is added which is no more than 3/4 inch thick, the usable aperture height will be a nominal 8.75 inches. We assume it would be best to remove the sides to allow the full 4 7/8 inch width. (Thus we calculated our 8.5 inch high by 5 inch (so we rounded up 1/8 inch!) wide usable aperture dimensions).


The conveyor bed will be approximately 60 inches long when completed with sprockets and a belt. The UHMW conveyor bed sits at a 44 inch working height on threaded rod adjustable feet. Complete with a pneumatic push-off reject cylinder with a stainless steel reject catch tray 10 inches long by 6 inches wide by 1 inch deep. The conveyor is configured for left-to-right product flow from the operator controls position, and the push-off goes from left to right from the perspective  of one standing at the infeed looking toward the discharge. Also mounted on the conveyor is a stainless steel power supply box for the metal detector. 110 volt single phase electrical input.

All food-grade sanitary stainless steel / washdown construction. Configured for vertical aperture orientation for containers, standing cartons, standing pouches, or other tall-product metal detection. This food process metal detection system has digital operator controls with product presets facilitating the fine tuning and quick changeover for multiple products.

As of this writing, this rectangular aperture metal detector is in stock in very good operational condition, available for immediate shipment as-is, or with reasonable lead time, can be completed by our shop with belt, sprockets and drive for a timely shipment.
Alard item reference #:Y1764

y1429

y1429d_email.jpgCOMMERCIAL MODEL NS-26 stainless steel "WATERFALL" CABBAGE / LETTUCE / ONION / GENERAL PURPOSE SLICER / SHREDDER.

26" diameter cutting disk, with 3-blade powered counter rotating plow achieve manufacturer rated cutting capacities of up to 10,000 lbs/hour, cutting "whole head" products (e.g. lettuce, cabbage) up to 9.5" diameter.

Stainless steel cutter with stainless steel blades, aluminum cutting disk frame, with aluminum feed plow, tubular stainless steel stand. Complete with (2) 3-phase drive motors, one each for cutting disk and plow, with operator control panel. An industry-standard sauerkraut cutter, and coleslaw cutter, this Waterfall type slicer / shredder is also commonly used for shredding lettuce, leafy greens, and other fresh vegetable products.

As of this writing, this 26 inch cabbage cutter is in stock in GOOD operational and mechanical condition, available for timely shipment.
Alard item reference #: Y1429

y1801

y1801c_email.jpgGroen 50 GALLON STEAM JACKETED KETTLE with Pardo horizontal SINGLE MOTION SCAPER-AGITATOR, Model P-CCHA-V-50. All sanitary stainless steel construction.

28 inch diameter by 29 inch deep hemispherical bottom Groen steam jacketed vessel with 3 inch center bottom outlet with Tri-clamp fitting. Stainless steel steam  jacket manufacturer tagged and National Board coded for 50 psi steam pressure.

HORIZONTAL scrape-surface agitation, with (7) plastic scrapers and two paddles in a single motion configuration, powered by a 1.5 HP 3 phase drive.

Includes a pneumatic Tri-flow sanitary valve with 3" Triclamp discharge fitting at a right angle, a hinged top cover, a thermal probe port, and (4) stainless steel legs set for a 46 inch infeed height.

IN stock in good condition, and available for timely shipment.
Alard item reference #:Y1801

y1755

METAL DETECTOR - SAFELINE DIGITAL STAINLESS STEEL CONVEYORIZED WASH-DOWN METAL DETECTION SYSTEM with PUSH-OFF REJECT, 14.75 inch high by 13.75 inch wide usable aperture opening.

y1755b_email.jpgThe all stainless steel washdown sealed search head is mounted on a stainless steel tubular frame BELT CONVEYOR. Previously used on a single belt long process line, this metal detector arrived with no belt or drive, and with 1/2 inch thick (each) UHMW sides running through the aperture, and is shown that way in our pictures of it. The overall aperture height of the search head is 16.75 inches high  by 13.75 inches wide, but as it now sits, configured with thick UHMW side rails and a 1 inch UHMW bed with no belt, the AS-IS aperture opening as shown in pictures is 15.5 inches high by 11.75 inches wide (between the sides). Assuming a belt is added which is no more than 3/4 inch thick, the usable aperture height will be a nominal 14.75 inches. We assume it would be best to remove the sides to allow the full 13.75 inch width. (Thus we calculated our 14.75 inch high by 13.75 inch wide usable aperture dimensions).  y1755c_email.jpg

The conveyor bed is now 64 inches overall length, without belt, drive or idler sprockets, and will be approximately 72 inches when completed with those. The UHMW conveyor bed sits at a 34.5 inch working height on threaded rod adjustable feet. Complete with a pneumatic push-off reject cylinder with a stainless steel reject catch tray 16 inches long by 12 inches wide by 1 inch deep. The conveyor is configured for right-to-left product flow from the operator controls position, and the push-off goes from right to left from the perspective of one standing at the infeed looking toward the discharge. Also mounted on the conveyor is a stainless steel power supply box for the metal detector. 110 volt single phase electrical input.

All food-grade sanitary stainless steel / wash-down construction. Configured for vertical aperture orientation for containers, standing cartons, standing pouches, or other tall-product metal detection. This food process metal detection system has digital operator controls with product presets facilitating the fine tuning and quick changeover for multiple products.

As of this writing, this rectangular aperture metal detector is in stock in very good operational condition, available for immediate shipment as-is, or with reasonable lead time, can be completed by our shop with belt, sprockets and drive for a timely shipment.

Alard item reference #:Y1755


y1678

y1678c_email.jpgERIEZ DIGITAL STAINLESS STEEL METAL DETECTOR with NEW STAINLESS STEEL THROUGH-CONVEYOR, 8 7/8 inch high by 26 inch wide usable aperture opening in stainless steel washdown sealed search head enclosure, with integral digital touch-screen operator controls. Overall aperture opening is 10 inch high, but the conveyor bed and belt take up an inch (and 1/8) the aperture height.

The stainless steel washdown-sealed reconditioned metal detector head is mounted on an all NEW stainless steel washdown belt conveyor, with a new 24 inch wide by 6 foot long interlocking plastic chain type belt, running over a UHMW plastic bed. 33 inch belt working height on 2 inch +/- adjustble feet. This tubular stainless steel frame belt conveyor is complete with a new wash-down gasketed PVC control box with a new 110 volt single phase washdown motor; all integrated with the search head to provide for a belt-stop-alarm reject system.

All stainless steel food grade sanitary washdown configuration. 110 volt single phase (standard household current) electrical input, with stainless steel Nema4 power supply box for the detection head.

As of this writing, this refurbished metal detector / new through-conveyor combination is IN stock in LIKE NEW condition, fully operational, ready to go and available for immediate shipment.
Alard item reference #:Y1678


y1267

y1267_email.jpgGRAVITY FLOW  METAL DETECTOR / DROP THROUGH METAL DETECTOR with REJECT VALVE, 6 inch diameter aperture opening, with 5 inch interior diameter UHMW plastic product pass-through tube. Digital operator controls.  Aluminum epoxy painted detector head mounted on a stainless steel support frame, with a pneumatic stainless steel reject diverter valve mechanism, with a 5 inch square/flangedproduct reject outlet, and a 5 inch square/flange good product outlet. Presently set for a 38" infeed height, on a stainless steel frame (discharge sits flat on the floor as configured, so needs to go up on something).

As of this writing this vertical packaging metal detector is in stock in very good operational condition, available for timely shipment.

Alard item reference #:Y1267

About this Archive

This page is an archive of entries from May 2013 listed from newest to oldest.

April 2013 is the previous archive.

June 2013 is the next archive.

Find recent content on the main index or look in the archives to find all content.


JOIN our
no-more-than-monthly

Email list!
Email PRIVACY explanation link!

ALARD EQUIPMENT CORP
6483 Lake Avenue
Williamson, NY  14589
315-589-4511
315-589-3871 (fax)