TRI-Clover TRI-BLENDER
/ POWDER DISPERSER / HIGH SHEAR MIXER

The Triclover Tri-Blender now also known as the Waukesha Cherry Burrell DTL BLENDER (since Tri-Clover was purchased by SPX) is manufacturer recommended for thoroughly & efficiently blending dry ingredients and liquids, or for blending two liquids into a homogenous mixture, while minimizing air introduction; in a variety of blending applications including food, beverage, dairy, chemical & pharmaceutical process production...

APPLICATIONS per manufacturer literature:

• Blending Stabilizers - such as with fresh milk, liquid eggs, ice cream mix.
  
  
• Blending Liquid Syrup - such as raw sugar and water.
  
  
• Blending Food Products - such as whey and water, powdered eggs to liquid, liquid syrup with liquid eggs and flavorings.
  
  
• Blending Chemical Products - such as sodium silicoaluminate, film solution, irium, fertilizer.

FEATURES:

• Manufacturer rated for absorbing dry powders into liquids at a rate of up to 100 lbs (45 kg) per minute.
  
  
• INLINE powder mixer / high-shear pump for continuous operation with uniform material absorbtion.
  
  
• 30 inch diameter by 24 inch deep cone hopper with 3 inch manually actuated butterfly valve.
  
  
• 7.25 inch 4-blade impeller powered by 10HP motor.
  
  
• 1.5 inch liquid inlet and 2 inch slurry discharge.
  
  
• USDA sanitary Tri-clamp connections.
  
  
• All food grade sanitary stainless steel construction including base and T316 stainless steel wetted parts.
  
  
• 460 volt 3 phase electrical input.

As of this writing, this high-shear mixer / blender / emulsifier / homogenizer / liquifier / powder dispersing machine is in stock at ALARD, in GOOD condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your food ingredient dispersion needs.

ALARD item reference #: Y4295

Urschel Model SL-A MEAT DICER, strip cutter, slicer,
VIDEO DEMO cutting meat cubes, dicing pork & chicken...

VIDEO DEMO
Urschel SL-A DICER cutting meat cubes, Y4563
from Alard Equipment Corporation.

The Urschel SL-A MEAT CUBE CUTTER is manufacturer recommended as designed for continuous operation, uniformly cutting dices, strip cuts or slices of cooked or raw frozen tempered meats, including, but not limited to pepperoni, hard salami, cooked roast beef, ham, pork, mutton, chicken, liver, seafood, fish, pet food, onions, and cabbage.

FEATURES:

• Manufacturer rated for infeed of firm products up to 4 inches (101.6mm) in any dimension.
  
  
• A three-dimensional cutter manufacturer rated for cuts (with appropriate change parts).
  
  
  • Slice knife cuts to 1/2 inch (12.7mm).
    
    
  • Circular knife cuts: 1/8 inch to 2 inches (3.2 to 50.8mm).
    
    
  • Crosscut kife cuts: 1/8 inch to 3 inches (3.2 to 76.2mm).
    
    
  • Many sizes and shapes of cut product can be produced by using some or all of the spindles and adjusting the slice thickness.
    
    
    • Slices can be produced by removing the circular and crosscut knife spindles.
      
      
    • Strip cuts can be made by removing the crosscut knife spindle, whence the length of the strips will depend on the size of the original product.
      
      
    • Note re cutting cubes / dices with all three spindles: This machine makes all three cuts on the cube separately, so the product is not crushed as it wouldl be on certain other types of dicing machinery.
      
      
  • CALL 315-589-4511 to discuss your specific industrial food process cutting application.

• Manufacturer literature rates the throughput capacity of this machine at 2,500 to 5,000 lbs per hour depending on cut size and product being processed.
  
  
• Food grade stainless steel USDA sanitary construction.

As of this writing, this Urschel SL-A meat cube and strip cutting machine is in stock at Alard, in EXCELLENT operational, mechanical, electrical and cosmetic condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability, and to discuss your particular industrial meat processing particle size reduction application.

Alard item reference #: Y4563

Gridpath VIBRATORY DEWATERING SHAKER /
VIBRATING FEED CONVEYOR, 89x36,
food grade stainless steel.

A Gridpath Solutions VIBRATING SHAKER, a vibratory shaker-grader feeder for grading, size sorting, fines removal, solids separation, water reclaim / dewatering, declumping and / or even-feeding downstream components...

FEATURES:

• 36 inch wide by 89.5 inch long vibrating conveyor bed.
  
  
  • 6 inch high stainless steel sides.
    
    
  • 8 inch long dimpled / rigidized solid sloped infeed section.
    
    
  • (2) 36 inch wide by 36 inch long stainless steel wedge-wire water reclaim / separator screens with 1/8 inch sieve openings running perpendicular to product flow.
    
    
  • 9.5 inch long dimpled / rigidized solid discharge section.
    
    
• Full length water collection pan with center bottom basin tapering to a 2.5 inch diameter pipe outlet.
  
  
• 47 inch infeed height, 44.5 inch high discharge.
  
  
• Heavy duty tubular frame with rubber isolation mounts.
  
  
• Quick release clamps for easy, tool-less removal & cleaning of screens.
  
  
• Vibratory action provided by two (2) 1/3 HP rotary / eccentric vibrator motors.
  
  
• All food grade sanitary stainless steel construction.
  
  
• 208 / 230 / 460 volt 3 phase electrical input.

As of this writing, this vibratory shaker-grader is in stock at ALARD, in EXCELLENT operational, mechanical, electrical & cosmetic condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your food handling needs.

ALARD item reference #: Y4520

BUTCHER BOY 250 stainless steel MEAT MIXER BLENDER,
TILT discharge.

A Butcher Boy model 250F, 250 lb capacity (8 cubic foot) single-motion PADDLE MIXER with TILT-to-dump discharge. Butcher Boy is focused on meat markets, but this food grade stainless steel horizontal mixer is appropriate for a wide range of food processing applications.

FEATURES:

• 31 inch long by 20 inch wide by 24 inch deep horizontal U-shaped stainless steel mixing vessel.
  
  
• Four (4) paddles, on a 1 inch diameter stainless steel shaft, with rectangular sweeps on each end.
  
  
• 50.5 inch infeed height.
  
  
• Manual tilt to dump with multiple position latch.
  
  
• Newly fabricated stainless steel lid with safety interlock system that cuts power when the lid is lifted.
  
  
• Locking 4 inch casters for added mobility.
  
  
• USDA food grade sanitary stainless steel construction.
  
  
• 2HP drive motor.
  
  
• 208 / 230 volt 3 phase electrical input.

As of this writing, this reconditioned Butcher Boy paddle blender is in stock at ALARD, in excellent operational, mechanical, electrical & cosmetic condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your food processing needs.

ALARD item reference #: Y4319

Groen 150 gallon STEAM-JACKETED KETTLE
with SINGLE MOTION SCRAPER-AGITATOR,
316 stainless steel.

A Groen N-150 KETTLE, steam jacketed with scrape-surface agitator, all food grade stainless steel with T316 stainless steel product contacts, and with center bottom outlet.

FEATURES:

• 42 inch by 35 inch deep hemispherical bottom vessel.
  
  
• Manufacturer tagged, National Board coded, and "U" stamped for 100 psi working pressure.
  
  
• Stainless steel bridge with 2.5 inch Tri-clamp inlet and removable helf-moon shaped lids.
  
  
• Single-motion scraper agitator with gear reduced 1.5 HP stainless steel shrouded drive motor.
  
  
• 50 inch high infeed.
  
  
• 3 inch center bottom outlet elbow.
  
  
• 2.5 inch Tri-clamp outlet with 7.5 inch high discharge.
  
  
• All food grade sanitary stainless steel, including legs, with T316 stainless steel product contacts.
  
  
• 208 / 230 / 460 volt 3 phase electrical input.

As of this writing, this Groen 150 gallon kettle with scraper agitator is in stock at ALARD, in good condition, available for timely shipment.

CALL 315-589-4511 to confirm availability and discuss your particular food process cooking kettle needs.

ALARD item reference #: Y4519

Hercon ELEVATING BELT CONVEYOR,
20 inch wide by 8 foot long cleated belt,
food grade stainless steel.

A food grade stainless steel elevating feed conveyor with cleated conveyor belt...

FEATURING:

• 8 foot long by 20 inch wide solid rubber cleated belt.
  
  
• 6 inch high sidewalls.
  
  
• Safety grids located over the belt.
  
  
• 32 inch infeed height, 76 inch discharge height.
  
  
• All heavy duty food gade sanitary stainless steel construction.
  
  
• Previously used in a USDA meat & cheese processing environment feeding blocks to a grinder.
  
  
• Top mounted 2HP gear motor drive.
  
  
• 230 / 460 volt 3 phase electrical input.

As of this writing, this elevating feed belt is in stock at ALARD, in GOOD condition, available AS-IS for immediate shipment -OR- can be serviced by our shop, including new belt, with timely shipment.

CALL 315-589-4511 to confirm availability and discuss your food process feed belt conveyor needs.

ALARD item reference #: Y4166

3-LEVEL INSPECTION BELT
/ CORING CONVEYOR / TRIM TABLE,
FRUIT and VEGETABLE PACKING CONVEYOR.

A three-conveyor inspection table, trimming line / coring line for hand-trimming, coring, sorting, grading, quality inspection and/or packing fruit & vegetable products into boxes or cases, in the context of fresh produce packing, or fresh cut / pre-cut produce packaging, frozen food, canning, and other industrial food processing applications. Consists of a main pick belt with an overhead sorted product takeaway conveyor and lower waste takeaway conveyor...

FEATURING:

• 10 inch wide by 16 foot long main belt with plastic open weave belting.
  
  
• 12 inch wide by 15 foot long top takeaway belt with food grade rubber belting.
  
  
• 15 inch wide by 15 foot long waste takeaway belt beneath with food grade rubber belting.
  
  
• Can be used as a six, seven or an eight-person trim line.
  
  
• 15 inch wide by 15 foot long waste takeaway belt beneath with a food grade rubber belt.
  
  
• Can be used as a six, seven or an eight-person trim line.
  
  
• Presently configured with (7) 6 inch diameter holes in the UHMW plastic trim-stations on each side of the main conveyor. (These can be re-configured at the time of order, per buyers specifications).
  
  
• All sanitary stainless steel construction.
  
  
• Individual fixed speed drives for each of the three (3) belt conveyors.
  
  
• 3 phase electrical input, per buyers specifications.
  
  

As of this writing, this inspection conveyor is in stock at Alard in good condition, available as-is for immediate shipment, or can be serviced by our shop for timely shipment per buyer specfication.

CALL 315-589-4511 to confirm availability, and to discuss your particular industrial food processing product inspection and grading equipment needs.

ALARD item reference #: Y4318

Refurbished URSCHEL Model H-A DICER,
cube cutter, strip cutter, slicer.

A three dimensional cutting machine for cubes, dices, and strip cuts, manufacturer rated for product input sized up to 5.5 inches (140mm) in any dimension. Manufacturer recommends for uniform dices, strips and slices, from a variety of soft ripe fruits and brittle root vegetables, such as potatoes, beets, lettuce, cabbage, broccoli, cauliflower, sweet potatoes, squash, carrots, mushrooms, turnips, cantaloupe, endive, tomatoes, cucumbers, horseradish, apples, grapefruit, citrus peel, papaya, pineapple, peaches, celery, rutabagas, melon rind, and may other foods; producing clean, uniform, high-quality tons-per-hour output...

Three cutting dimensions:

• Slice thickness from 1/8 inch (3.2mm) up to 3/4 inch (19.1mm) -- knob adjustable.
  
  
• Circular knives from 1/8 inch (3.2mm) to 3 inch (76mm) -- spacers and number of knives determine.
  
  
• Crosscut knife spindle spacing from 3/4 inch (19.1mm) up to 1.75 inches (44.5mm) -- change part. By removing the crosscut knife spindle and/or the circular knife spindles(s), the Urschel HA dicer can also cut strips cuts (two-dimesnional cuts) such as forFrench fries and slices (single dimension cut).
  
  
• An optional "G" kit is available to extend the range of this machine to overlap with the Urschel model G, and we can otherwise complete this machine with cutting parts to buyer specification -- CALL 315-589-4511 to discuss your particular food process cutting machine need!
  
  

FEATURES:

• Stainless steel product contact surfaces, including slice shell and impeller with 7 inch slice shell opening, cutting spindles and knives.
  
  
• USDA sanitary model designation with food grade stainless steel construction including spindle arms, guards, shrouds and tubular stainless steel frame.
  
  
• Factory control box with safety interlock system.
  
  
• Standard 2 HP 208/230/460 volt 3 phase drive.

As of this writing, this reconditioned Urschel dicer is in stock at ALARD, in EXCELLENT operatonal, mechanical, electrical & cosmetic condition, needing only to be fitted with cutting parts to buyer specification prior to shipment.


CALL 315-589-4511 to confirm availability and discuss your particular industrial food process cutting machine needs.

ALARD item reference #: Y4527

GROEN INA/2-200, 200 Gallon
STEAM JACKETED KETTLE
with INCLINED SCRAPER-AGITATOR.

A 200 gallon capacity 100 psi steam-jacketed cooking kettle with scrape-surface agitation from an incline agitator, USDA food grade sanitary stainless steel with temperature probe port...

FEATURES:

• 42 inch diameter by 45 inch deep hemispherical bottom vessel with 3 inch center bottom outlet.
  
  
• Manufacturer tagged and National Board coded for 100 psi working pressure.
  
  
• Inclined scraper-agitator with drive geared for 33 RPM at the agitator.
  
  
• 3 inch diameter center bottom outlet.
  
  
• Temperature probe port.
  
  
• USDA sanitary food grade stainless steel construction, including the (3) pipe legs.
  
  
• 1.5 HP 208/230/460 volt 3 phase agitator drive motor.

As of this wriing, this Groen 200 gallon kettle with scraper agitator is in stock at ALARD, in GOOD operational, mechanical & cosmetic condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your particular food process cooking kettle needs.

ALARD item reference #: Y4399

50 HP VERTICAL STEAM BOILER
150psi, natural gas STEAM GENERATOR

This Clayton Industries STEAM GENERATOR, SigmaFire model SF-50, natural gas-fired boiler is a compact vertical package / skid mounted, fuel-efficient steam boiler for producing high quality steam for industrial applications...

SPECIFICATIONS: Manufacturer tag data...

• National Board Coded number 24757.
  
  
• 150 psi working pressure.
  
  
• 1,725 pounds of steam per hour at 212 degrees Farenheit.

FEATURES: Per Manufacturer literature...

• Single pass design.
  
  
• 1,969,118 BTU / hour input, 1,673,750 BTU / hour output -- 85% efficiency.
  
  
• Rated for 265 gallons per hour water capacity.
  
  
• 2 HP blower motor.
  
  
• 110 volt single phase control circuit.
  
  
• 208 / 230 volt 3 phase electrical input.

As of this writing, this used natural gas fired 50HP steam boiler is in stock at ALARD, in unused LIKE NEW condition and available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your particular food process steam generation requirement.

ALARD item reference #: Y4540

ARPAC Model 105-28TW
TRAY WRAPPER / HEAT SHRINK BUNDLER...

An ARPAC Model 105-28TW / 105 series continuous motion shrink bundler. As trays of containers or other bundles proceed through this machine they are wrapped around their wide sides, then run thru the heat tunnel to shrink the plastic tightly around the trays / bundles, leaving "bulls eye" openings in the plastic wrapping on each (narrow) end. Manufacturer recommended for trays of cans, jars, bottles, trayed boxes, single-tier or stacked, and unitized boxes.

FEATURES:

• Manufacturer rated for up to 28 trays per minute throughput capacity.
  
  
• Dual top and bottom film roll spools.
  
  
• Wrapper / bindler section has 14 inch wide by 72 inch long roller bed thru-conveyor.
  
  
• 28 inch seal bar with 11 inch maximum clearance.
  
  
• Heat shrink tunnel has a 28 inch wide by 15 inch high opening, 22 inch wide heat resistant rubberized belt thru conveyor, one (1) intreior heat circulation fan, one (1) exterior cooling fan and mechanical cariable speed conveyor drive.
  
  
• Painted steel construction.
  
  
• 575 volt 3 phase electrical input.
  
  As of this writing, this tray wrapper with heat tunnel is in stock at ALARD, in GOOD condition and available for immediate shipment.
  
  CALL 315-589-4511 to confirm availability and discuss your food packaging needs.
  
  ALARD item reference #: Y4032
  
  

URSCHEL DIVERSACUT SPRINT DICER...

A versatile, compact, high-capacity industrial food process cutting machine, dicer, slicer, julienne cutter, which uniformly cuts flat or crinkle cut dices, cubes, strips / strip cuts, french fry cuts, and slices from a wide variety of food products at high production capacities with speeds dependent on materials, application and machine configuration...

Manufacturer SPECIFICATIONS:

• Slice shell cuts 1/16 inch to 1 inch (1.6mm to 25.4mm) -- knob adjustable.
  
  
• Circular knife cuts 1/8 inch to 3 inches (3.2mm to 76.2mm) -- spindle with knives and spacers.
  
  
• Crosscut knife cuts from 3/32 inch to 1 inch (2.4mm to 25.4mm) -- change part.
  
  
• Maximum product infeed size of 6.5 inch (165 mm) in any dimension.
  
  
• Flat or krinkle-cut cutting parts can be used in various combinations for cubes, strip cuts, rectangular cuts, julienne cuts, slices, flat or krinkle-cut french fry strips. Works as a one-dimensional slicer, two-dimensional or three-dimensional cutter. CALL 315-589-4511 to discuss YOUR particular food process cutting machine requirements.
  
  
• This cutter is manufacturer recommended for a wide range of fruit, vegetable and meat cutting applications, including flat or crinkle cut French fries, ham, salmon, strawberries, carrots, tomatoes, green peppers, and many more food items.

FEATURES:

• 18 inch long by 16 inch wide top hopper extension over a 14.75 inch long by 15.5 inch bottom hopper feeding to the slice shell.
  
  
• 9 inch slice shell opening, 14 inch diameter CRINKLE slice shell cutting chamber.
  
  
• 20 inch long by 10 inch wide discharge chute.
  
  
• On tubular stainless steel support stand with locking casters, at a 77 inch infeed height, 33 inch discharge height.
  
  
• Food grade USDA sanitary stainless steel construction with hinged access panels for ease of sanitation and maintenance.
  
  
• Factory electrical control panel with safety interlock system.
  
  
• 1.5 HP 208/230 volt 3 phase stainless steel shrouded motor drive.

As of this writing, this Urschel Sprint DICER is in stock at Alard, ready-to-go in LIKE NEW operational, mechanical, electrical & cosmetic condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your particular food process cutting machine requirements.

ALARD item reference #: Y4606

ELEVATING BELT CONVEYOR with HOPPER,
12 inch wide, food grade, stainless steel, cleated belt...

The Vanmark Model 1405 EVEN FEEDER CONVEYOR is manufacturer recommended for consistent dry product feeding flow for fruit and vegetable products including apples, beets, carrots, cucumbers, onions, potatoes and other root crop vegetables. This incline feed conveyor with five-sided in-feed hopper is sturdily-built in food grade sanitary stainless steel, and is configured with a high discharge height for feeding a Vanmark abrasive peeler / brush washer (not included) or other elevated downstream equipment; for industrial food processing and packing applications.

FEATURES:

• 12 inch wide by 8.5 foot long incline belt.
  
  
• Cleated belt with 1 inch high cleats on 3 inch centers.
  
  
• The belt runs between 7.5 inch high sides flared to 17 inches wide at the tops.
  
  
• 21 inch wide by 15 inch long tapered stainless steel feed hopper.
  
  
• 33 inch infeed height, 67 inch high discharge.
  
  
• All food grade sanitary stainless steel construction.
  
  
• Top mounted 3/4 HP drive motor.
  
  
• 208 / 230 / 460 volt 3 phase electrical input.

As of this writing, this elevating belt conveyor is in stock at ALARD, in EXCELLENT operational, mechanical, electrical & cosmetic condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your industrial food processing and packaging bulk food handling needs.

ALARD item reference #: Y4610

Key Iso-Flo VIBRATING DEWATERING SHAKER,
vibratory size grader, even-feeder,
72x24, all stainless steel....

A 6x2 Key Iso-Flo vibratory shaker-grader with quick-release interchangeable screen and bottom catch pan, for dewatering, grading, size sorting, fines removal, grading out shorts, solids separation, and vibratory even-feeding to downstream components.

FEATURES:

• 24 inch wide by 6 foot long shaker bed.
  
  
  • 6 inch long dimpled / rigidized solid surface infeed.
    
    
  • 1/2 inch drop to 30 inch long screen with 1 inch diameter perforations and quick-release screen retainer hooks for fast screen replacement / changeover.
    
    
  • 1/2 inch drop to 30 inch long screen with 1 inch diameter perforations and quick-release screen retainer hooks for fast screen replacement / changeover.
    
    
  • 1/2 inch drop to 6 inch long dimpled / rigidized solid surface discharge.
    
    
• 6 inch high sides.
  
  
• 60 inch infeed height, 54 inch discharge height.
  
  
• Plastic bottom pan with 6 inch diameter center bottom outlet.
  
  
• All food grade sanitary stainless steel construction including frame and pedestal legs.
  
  
• New style Key Iso-Flo eccentric with 1HP drive motor.
  
  
• 208 / 230 / 460 volt 3 phase electrical input.

As of this writing, this vibrating conveyor is in stock at ALARD, in EXCELLENT operational, mechanical and cosmetic condition, ready to go and available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your particular food process conveying equipment needs.

ALARD item reference #: Y4569

HOT WATER ROTARY BLANCHER,
6 x 4, stainless steel...

An A.K. Robins Model AK-48-6, all USDA stainless steel rotary drum blancher for vegetables, pasta, dry beans, pet foods, and a variety of products in an industrial food processing and production line context...

FEATURING:

• 48 inch (4 foot) diameter by 6 foot long stainless steel blancher reel.
  
  
• 1/8 inch screen perforations in rotary blanching drum with removable screen panels for sanitation.
  
  
• Steam injection sparge at infeed side.
  
  
• Hinged, counterweighted top cover.
  
  
• 60 inch infeed height.
  
  
• Overflow discharge to dimpled discharge chute with 31 inch discharge height.
  
  
• Two (2) 10 inch diameter bottom end clean out plates.
  
  
• USDA food grade sanitary stainless steel construction.
  
  
• 2HP drive motor, 208/230/460 volt 3 phase electrical input.

As of this writing, this hot water rotary blanching machine is in stock at ALARD, in EXCELLENT operational, mechanical, electrical & cosmetic condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability, and to discuss your particular industrial food process cooking and blanching equipment needs.

ALARD item reference #: Y4212

IMMERSION WASHER-CHILLER, dip tank,
with CONVEYOR belt discharge,
all stainless steel...

VIDEO DEMO
IMMERSION WASHER-CHILLER, dip tank, with CONVEYOR belt discharge, Y4594
from Alard Equipment Corporation.

T.S. DESIGN JR. WASH & CHILL, manufacturer recommended for use on almost any produce product, whether whole or pre-cut fruit or fresh-cut vegetables. Designed as a compact washing and chilling system to provide maximum utility in a small footprint.

FEATURES:

• 78 inch long by 24 inch wide by 28 inch deep turbulent wash tank.
  
  
• Multi head spray system over the wash tank to assure submersion and uniform exposure to the cooling water and / or sanitizing or preservative solution.
  
  
• 18 inch wide perforated food grade plastic mesh discharge conveyor with variable speed control for just the right wash.
  
  
• Includes recirculation pump with stainless steel motor.
  
  
• Side mounted .025 inch hydrosieve screen effectively filters wash water of leaves, stems, fines, and other debris resulting from the washing process.
  
  
• 36 inch high inheed, 40 inch discharge height.
  
  
• Conveyor tilts / lifts out for ease of sanitation.
  
  
• Forty (40) pass 1 inch diameter by 6 foot long stainless steel chill lines - previously used for FREON but could be plumbed for chilled water or glycol.
  
  
• All sanitary stainless steel construction.
  
  
• 208 / 230 volt 3 phase electrical input.
  
  
• Very late model, current state of the art cooler-washer system.
  

As of this writing, this turbulent cooler-washer is in stock at ALARD, in EXCELLENT condition and available for timely shipment.

CALL 315-589-4511 to confirm availability and discuss your food processing needs.

ALARD item reference #: Y4594

DEMO VIDEO
SINGLE-STATION
NETWEIGH BAG FILLING TABLE,
with wash-down scale,
and adjustable height pneumatic bag-holder,
all food grade stainless steel...

DEMO VIDEO
Single station BAGGING TABLE for pre-cut PRODUCE packing, Y0500
from Alard Equipment Corporation.

A food grade sanitary stainless steel BAG PACKING TABLE / hand-pack bag filler for fresh-cut produce packaging, with a remote readout scale, and adjustable height pneumatic bag-holder, for filling pre-cut produce and other food products into bags by weight. Ideal for whole, diced, or chopped vegetables and fruits, shredded or whole leafy vegetable products, and salad mixes.

OPERATION:

• The operator hangs the bag on the bag-filling funnel and engages the bag holder by pressing a button.
  
  
• The operator then pulls product by hand, from the table into the filling tube, until the proper weight is made, as indicated by the eye-level over/under scale. A little product easily be remove if needed to "make weight".
  
  
• The operator then disengages the bag holder and removes the bag, puts a new bag in place, and the process is repeated.
  
  

FEATURES:

• The stainless steel bag-filler / pack table is 43 inches long by 37.5 inches wide inner/working dimensions, and has sides that taper from 14 inches high at the back, and angles down to 6 inches high at the front.
  
  
• 30 pound capacity Cardinal wash-down over-under scale, with remote readout mounted at eye level. Other model scales / capacity are/is available to customer specification; CALL 315-589-4511 to discuss your particular fruit and/or vegetable bag weigh-filler specifications.
  
  
• 6.25 inch diameter front center filling tube. (Can be supplied with filling tube inserts for smaller size bags).
  
  
• Stainless steel pneumatic bag holder with push-button operator control for holding bag on the filling tube.
  
  
• Beneath the bag holder is a 12 inch wide by 10 inch front-to-back stainless steel weigh cell platform which is adjustable to accommodate different bag heights.
  
  
• 40 inch working height at front lip, on threaded rod adjustable feet with foot-pads. NOTE: Pictures show optional casters, available at extra-cost; --call 315-589-4511 to discuss your specific pack table specifications.
  
  
• All food grade sanitary stainless steel construction.
  
  
• 110 volt single phase electrical input (standard household current) for the scales, and requires compressed air for the bag holders.
  

While we occasionally sell out of on-hand machnines, we maintain this by-hand bag-filler in stock as continuously as possible; --NEW, fully assembled, ready to go and available for immediate shipment.


CALL 315-589-4511 to confirm present availability, and to discuss your particular pre-cut produce / fresh produce packaging equipment needs.

You may view a pictures of this machine at
http://www.alard-equipment.com/a-f/y0500sne.htm
on our general listings page under "F" for FILLER, BAG....

Alard item reference #:Y0500

VIDEO DEMO cutting cabbage on a
COMMERCIAL CABBAGE CUTTER, 26 INCH,
industrial-capacity food grade stainless steel
vegetable SLICER / SHREDDER / STRIP CUTTER...

DEMO VIDEO
Commercial NS26 SLICER, shredder Y4497
from Alard Equipment Corporation.

A Commercial Slicer Model 26NS, also known as a "Waterfall" slicer or Kibbey cutter, has long been the mainstay of the coleslaw and sauerkraut industries. Manufacturer recommended for lettuce, cabbage, onions, peppers, cucumbers, potatoes,carrots, tomatoes and celery...

FEATURING:

• 26 inch diameter aluminum frame cutting disk with stainless steel knives; 100% cutting surface.
  
  
• "Three cup" counter-rotating aluminum carrying arm pusher-plow to prevent rolling and maximize throughput capacity.
  
  
• Open infeed to easily accept heads of cabbage, lettuce and other whole vegetable products (up to 9 inch diameter).
  
  
• Manufacturer rated for up to 25,000 pounds per hour, depending on cut size and product.
  
  
• A range of cutting disk and blade configurations are available for one and two-dimensional cutting (slices, strip cuts, julienne cuts) in thicknesses from 1/32 to 2 inch and up to 5 inch in length. Grater blades are also available forshredding carrots, slaw, onions, and other fresh vegetables. CALL 315-589-4511 to discuss your particular industrial food process vegetable cutting / cut size specification.
  
  
• Food grade stainless steel construction, including tubular stainless steel frame, with 52 inch infeed height and 19.5 inch high discharge and funneled discharge with 24 inch by 24 inch discharge opening.
  
  
• Complete with two (2) 1.5HP gear motor drives - one for main cutting wheel and the other powers plow.
  
  
• 230 / 460 volt 3 phase electrical input.

As of this writing this high-capacity industrial slicing and strip cutting machine is in stock at ALARD, in good condition, available for timely shipment.

CALL 315-589-4511 to confirm availability and discuss your food process fruit and vegetable slicing and strip cutting needs.

ALARD item reference #: Y4497